View LB11988HR_4345078.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENA0300
LB11988HR
Overview
Monolithic Digital IC
Fan Motor Driver
The LB11988HR is a motor driver IC optimal for driving the automotive fan motors.
Features
* 3-Phase full-wave current-linear drive system. * Current limiter circuit built in. * Output stage upper/lower over-saturation prevention circuit built in. * Forward/backward rotation direction setting circuit built in. * FG amplifier built in. * Thermal shutdown circuit built in. Absolute Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Symbol VCC max VS max Maximum output current Allowable power dissipation Operating temperature range Storage temperature range IO max Pd max Topr Tstg Independent IC Conditions Ratings 24 24 1.3 0.8 -40 to +85 -55 to +150 Unit V V A W C C
Allowable Operating Range at Ta = 25C
Parameter Supply voltage VS VCC Hall input amplitude VHALL Between hall inputs Symbol Conditions Ratings 5 to 22 5 to 22 30 to 80 mVo-p Unit V
Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before usingany SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein.
83006 / 52506 MH IM B8-7845 No.A0300-1/8
LB11988HR
Electrical Characteristics at Ta = 25C, VCC = 12V, VS = 12V
Parameter VCC supply current Output Output saturation voltage VOsat1 VOsat2 IO = 500mA, Rf = 0.5, Sink+Source (with saturation prevention) IO = 1.0A, Rf = 0, Sink+Source (with saturation prevention) Output leakage current Hall amplifier Input offset voltage Input bias current Common-mode input voltage Voff(HALL) Ib(HALL) Vcm1(HALL) Vcm2(HALL) FR Threshold voltage Input bias current Current limit LIM pin current limit level Saturation Saturation prevention circuit lower set voltage FG Amplifier Output "High" voltage Output "Low" voltage Hysteresis width TSD operating temperature Vfgoh(SH) Vfgol(SH) Vhys TTSD Design target value* 23 170 11.8 0.3 mV C V VOsat(DET) RL = 560 (Y),Rf = 0.5 Voltage between each OUT and RF 0.28 V ILIM Rf = 0.5, Hall input logic fixed (U, V, W = H, H, L) 1 A VFRTH Ib(FR) 4 -5 8 V A VIN, WIN VCC = VS = 12V VCC = VS = 5V 3 1.5 -6 1 +6 3 VCC-3 VCC-1.5 mV A V IOleak 2.1 2.6 V 2.6 3.5 1.0 mA Symbol ICC RL = 560 (Y) Conditions min Ratings typ 15 max 24 mA unit
*: T-TSD is not measured because it stands for design target.
Package Dimensions
unit : mm 3233B
HEAT SPREADER (4.9) 10.5 7.9
0.25 2.0 0.3 15.2 (6.2) 28 15
1 0.8 (0.8)
14
2.7
0.1
(2.25)
2.45max
SANYO : HSOP28H(375mil)
0.65
No.A0300-2/8
LB11988HR
1.0
Pd max - Ta
Independent IC
Allowable Power Dissipation,Pd max - W
0.8
0.8
0.6 0.42 0.4
0.2
0 -40
-20
0
20
40
60
80
100
Ambient Temperature, Ta- C
ILB01758
Truth Table and Control Function
Source Sink VW WV UW WU UV VU WV VW WU UW VU UV Hall Input U H V H W L H L H L L H L H L H H L L L H H L L H H H L L H L H L FR
1
2
3
4
5
Note: "H" in the FR column represents a voltage of 8V or more. "L" represents a voltage of 4V or less. (At VCC=12V) Note: "H" under the Hall Input columns represents a state in which "+" has a potential which is higher by 0.01V or more than that of the "-" phase inputs. Conversely "L" represents a state in which "+" has a potential which is lower by 0.01V or more than that of the "-" phase inputs. Note: Since a 180 energized system is used as a drive system, other phases than the sink and source are not OFF.
6
No.A0300-3/8
LB11988HR
Pin Assignment
WOUT 1 NC 2
28
VOUT
27 26
UOUT NC
NC
3
FGOUT NC
4 5
25 24 23
NC
NC RF VS
FR GND
6
7
22
LB11988HR
NC FC 8 9 21 VCC NC
20 19
NC 10 NC 11 UIN+ 12 UINVIN+ 13
WINWIN+ VINNC
18 17 16
14
15
NC
Top view
No.A0300-4/8
LB11988HR
Pin Functions
Pin Name VCC Pin No. 21 Input/Output Equivalent Circuit Pin Functions Power supply pin for supplying power to all circuits expect output section in IC; this voltage must be stabilized so as to eliminate ripple and noise. GND 7 FRAME UIN+, UIN12,13 GND for others than the output transistor. Minimum potential of output transistor is at RF pin.
Each (+) input 18
Each (-) input 19 17
U-phase Hall device input pin; logic "H" presents IN+>INV-phase Hall device input pin; logic "H" presents IN+>INW-phase Hall device input pin; logic "H" presents IN+>IN-
VIN+, VIN-
14,17
14 100A 12 200 200
13
WIN+,WIN-
18,19
UOUT VOUT WOUT RF
27 28 1
U-phase output pin. V-phase output pin. W-phase output pin.
22 VS
23
VCC 150A
(Built-in spark killer diode) Output current detection pin. Connecting Rf between this pin and GND activates current limiting circuit. Then the lower over-saturation prevention circuit is activated in accordance with this pin voltage. Since the over-saturation prevention level is set with this voltage, the lower over-saturation prevention effect may deteriorate in the high current range if the Rf value is reduced to an extremely low level.
Each OUT 27 28 1
23 RF
VS FR
22 6
30k
200
Lower oversaturation prevention circuit block
Power supply pin for supplying power to output section in IC. Forward/Reverse switching pin.
VCC 200A 200 FR 6 1/2VCC
Continued on next page.
No.A0300-5/8
LB11988HR
Continued from preceding page.
Pin Name FC Pin No. 9 Input/Output Equivalent Circuit Pin Functions Frequency characteristics compensation pin for over-saturation prevention circuit loop.
VCC
10k
9 FC
FGOUT
4
VCC 10k 5k
VCC
FG amplifier output pin. Resistive load provided internally.
4 FGOUT
No.A0300-6/8
0.1F FC 9 22 VS
Block Diagram
VCC
UIN+ 12
13 UINUOUT VOUT WOUT
VIN+ 14
17 VINWIN+ 18
Hall input combination unit (linear matrix)
Combined output logarithmic compression unit
Logarithmic inverse transformation & differential distribution
27 28 1 0.1Fx3
19 WIN23 Upper saturation prevention control Drive distribution circuit & lower saturation prevention control VCC LIMREF Schmidt amplifier 5k Current limitter TSD UIN+ 13.6k GND 7 UINFG amplifier 30k 4 FGOUT RF
FR 6
Forward/Reverse switching
0.5
Differential distribution Feedback amplifier
LB11988HR
Bandgap 1.2V
VCC
21
Reference voltage
No.A0300-7/8
LB11988HR
Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of May, 2006. Specifications and information herein are subject to change without notice.
PS No.A0300-8/8

▲Up To Search▲

Price & Availability of LB11988HR

	To Download LB11988HR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .